Search:
Shopping Cart
Your account
Cash box
Shipping & Returns
Privacy Notice
Conditions of Use
Impressum
Contact
Main page
»
Catalogue
»
Engines / Accessories
»
Richter adjustable motor mount for 30-180 cc engines
Shopping Cart
You do not have any products in your shopping cart yet.
Shopping Cart »
Categories
Motorplanes
Sailplanes
CFK Spinner
GRP / CFRP components
Servo / Accessories
Cable / Connector
Fuel tanks and hoses
Screws / nuts
Wheels / Axles
Linkage
Aluminum / CFRP tubes
Slides
Tools
Epoxy / Adhesives
Smoke / Accessories
Elbow / Stainless Steel
Engines / Accessories
• spark
silencer
Other accessories
Stickers
fiber composites
Meters
LED lighting
Model tape
Reviews
Review this product!
Manufacturer
Please choose
3M™
DAVE BROWN PRODUCTS ..
DLA Engines
DLE Engines
EMCOTEC
Enrico Richter Model..
Festo
Flugmodellbau-Berlin
flyingtoolbox aviati..
Gabiel Stahlformenba..
Hitec
Jamara
KAVAN
Krumscheid
MJM Modellbau James ..
Nona Air
ORACOVER
Petrausch Modellbaut..
PowerBox Systems
Smoke-EL
Weatronic
Yuki Model
Quick purchase
Please enter the article number from our catalogue.
Richter adjustable motor mount for 30-180 cc engines
from 49,90 EUR
incl. 19 % Tax excl.
Shipping costs
Shipping time:14 Days
, Richter "motor mount adjustable
In this embodiment, the rear wheels are provided with a fine thread M16x1.
In addition, spacers with a diameter of 16mm and a length of 50mm in the kit are included.
The thread can be screwed to about 15mm in each other.
A groove in the pin at about 7mm indicates the minimum length, so that the best possible force transmission takes place.
The bolt should be reduced prior to installation on rough length in a lathe.
This motor mount is very easy to adjust the exact distance between the bonnet and spinners.
Also, the sideways engine and crash in a small extent be corrected.
For the exact adjustment of the threaded standoffs should be well glued with thread lock.
The engine mount is designed for single-cylinder engines and boxer 30 - 180ccm. It is constructed so that the motor carrier is screwed to the four rubber parts nose bulkhead with M5 bolts. The brass spacer sleeves must be adjusted so as to retain the damping properties of the rubber stay. The gums are pressed together about 0.2-0.3 mm, and is not pressed as in the use of D-locomotives which the rubber together is hardly any vibration absorption occurs. The holder consists of twisted cover and in each of which Fußscheiben a spacer sleeve is inserted into a precisely cut. This will spacer sleeve and cover plates to form a unit. The motor mount is secure in the rubber elements., The difference from the old version is the that the rubber elements are not full area in the bore of the motor carrier sit, but are used with rubber nubs on the slight tension in the hole. Thus at the narrowest point on the transition from motor mount to the hull creates an optimal vibration absorption in crankshaft rotation, and not, as with the use of D-locomotives being squeezed this is exactly where the rubber. It, even with this motor mount hinged easily the carburetor linkage be. The bracket weighs about 100 grams and is therefore only about 40g heavier than when D-locomotives are used. The only difference in the installation of the new version is that the holes in the motor mount 16mm instead of 14mm are. Thus, all motor mounts, the old version with the new rubber elements are retrofitted (retrofit kit available for 15 ¤) The aluminum parts have a diameter of 32mm.Die build elements of nose bulkhead to the rear edge firewall to about 7mm. Advantage of this mount is:-preventing dangerous vibration tips, looks sound dampers,-the engine can be governed at idle much more than the use of a hydraulic mount (no shaking), this results in a smaller landing speed, no maintenance,-no departures from gums possible, so much safer. When installed correctly and no shaking of the model, as in the use of mounting pads is possible. The vibration sensor can be adjusted by the length of the spacer sleeves depending on the model. The spacers are designed for motor mounts of6 to 8mm. Smaller motors can also be fitted directly, and the rubber used in the nose bulkhead. Tests have shown that the use of such a support, with respect to a fixed mounting of the motor doubles the lifetime of the aileron servo gear about. There is a detailed installation instructions. In RC Groups Review there. All model flyers should incorporate into its expensive models ever to be highest security model to protect themselves and others from harm. This product is in great measure to this. Anyone who still doubts should let me think what does a servo gear!
This Product was added to our catalogue on Tuesday, 20. November 2012.
Customers who bought this product bought also the following products:
Aramid Carbon Rear Suspension
from 23,90 EUR
Schlauchverbinder klein
from 1,90 EUR
Resonanzrohrhalterung für ø 50-52 mm
from 18,50 EUR
Bearings 16 x 6 x 5 mm
from 1,60 EUR
CFK Servohebelarm Typ A max. 52 mm Anschraubpunkt / für Futaba
from 3,90 EUR
Aluminum clevis M3
from 2,99 EUR
[<<First]
|
[<Back]
|
[Next>]
|
[last>>]
|
15
Articles in this categorie
Available soon at our shop!
Informations
Sitemap
eCommerce Engine © 2006
xt:Commerce Shopsoftware
Parse Time: 0.074s