Shopping Cart

You do not have any products in your shopping cart yet.
Shopping Cart »

Categories

 

Reviews

Information about manufacturer

Enrico Richter Modellbau
More Products

Manufacturer

Quick purchase

Please enter the article number from our catalogue.




Richter Motor Mount for 30 - 180 (222) cc engines
Richter Motor Mount for 30 - 180 (222) cc engines

from 29,90 EUR

incl. 19 % Tax excl.

Shipping time:14 Days

Richter Motor Mount for 30 - 180 (222) cc engines
Richter Motor Mount for 30 - 180 (222) cc engines
Richter Motor Mount for 30 - 180 (222) cc engines


New version with better damping properties

The engine mount is designed for single and boxer engines from 30 to (222) 180ccm constructed.

It is structured so that the motor carrier in 4 rubber parts on Kopfspant with M5 screw is screwed.

The brass sleeve spacing must be set so that the damping properties of the rubber remain intact.

The gums are approximately 0.2-0.3 mm compressed, and not as the use of D-locks to the rubber is pressed together, the lack of any vibration recording takes place.

The holder is made of twisted deck and Fußscheiben where one sleeve spacing exactly a cut is used.

This distance sleeve and shields into a single unit. The motor carrier is sitting safely in the rubber elements.

The difference to the old version is that the rubber elements are not completely in the bore of the motor vehicle seat, but by pimples on the gums with mild prestress in the hole can be used.

This gives rise to the narrowest point on the transition of the motor carrier to an optimal hull vibration reception in the direction of crankshaft rotation, and not as the use of D-Lock is precisely at this point of the rubber is squeezed.

It can also be used for mounting this engine without any problems with the carburetor rods are hinged.

The mounting weighs approximately 100 grams and is only about 40g heavier than when D-locks are used.

The only difference in the cultivation of the new version is that the holes in the engine makers are 16mm instead of 14mm.

Therefore, all motor mounts the old version with new rubber elements retrofittable (retrofit kit available for 15 ¤) The aluminum parts have a diameter of 32mm.

The elements of Kopfspant built up trailing edge Motorspant approximately 7mm at.

Advantage of this mount is vibration-preventing dangerous spikes, noise-dampening effect, the engine can Standgas in abgeregelt much further than when using a Hydromaunt (no shaking), it follows a smaller landing speed, no maintenance, no departures from gums possible, much safer.

With proper installation is also not Aufschütteln of the model, as the use of rubber vibrating elements possible.

The oscillation can be achieved by recording the distance length sleeves depending on the model to be adjusted.

The parts are available for Motorspanten von6 to 7mm ausgelegt.Kleinere engines can also be screwed directly, and the rubber used in Kopfspant.

Tests have shown that the use of such a bracket, compared to a fixed mounting of the engine life of the Querruderservogetriebe roughly doubled.

It is a precise assembly instructions bei.In RC network model, there are Testberichte.Jeder its pilots should always expensive models incorporate the highest security to its model, himself and others to protect from harm.

This product carries a high level to this.

Those who still doubt the times should be superior to what a servo gear costs!

This Product was added to our catalogue on Sunday, 26. April 2009.

Customers who bought this product bought also the following products:

10 Nylon-RUDDER HINGE 34 x 16 mm
Fuel tank square-1500ml

Fuel tank square-1500ml

from 7,50 EUR
Aluminum bell crank 30 or 50 mm with M3 collar
5 m PVC soft power cable 3-wire twisted 0.25 mm ²
CFK Servohebelarm Typ A max. 52 mm Anschraubpunkt / für Futaba
1 m stainless steel tube extremely thin in ⌀ 2 - 6 mm (out

[Next>] | [last>>] | 15 Articles in this categorie

Available soon at our shop!

Informations

Parse Time: 0.085s